Return to Hobie.com
Hobie Forums
It is currently Thu Mar 28, 2024 5:52 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: Turbo Fin reinforcement
PostPosted: Tue Jul 31, 2012 6:06 am 
Offline
Site Rank - Captain

Joined: Sat Jun 28, 2008 2:14 pm
Posts: 32
We have older ST Turbo fins and found that they accumulate a lots of scrapes and cuts, especially in the bottom 1 - 2 inches. I've searched the archives and found a lot of posts on repairing damage, but not so much on preventing or reducing damage.

I've experimented with EPDM (rubber roofing membrane) patches as shown below. Seems to help, and doesn't seem to have any noticeable effect on performance (though I'd probably not do this if I were racing).

Any other ideas / suggestions? Are the newer fins a tougher material such that this isn't necessary or advisable?

Image

_________________
2x Revo
17' Grumman Ultralight


Top
 Profile  
 
PostPosted: Tue Jul 31, 2012 7:34 am 
Offline
Site Rank - Old Salt

Joined: Mon Jun 01, 2009 11:59 am
Posts: 606
The best advice I can give you is to pull the drive if in water less than 6 inches deep. Just my two cents worth. Good Luck with repairs.


Top
 Profile  
 
PostPosted: Tue Jul 31, 2012 9:45 am 
Offline
Site Rank - Captain

Joined: Sat Jun 28, 2008 2:14 pm
Posts: 32
Despite best efforts and careful usage, we still seem to get a lot of cuts and scrapes (some of them on the kayak). Leading causes seem to be:

1) Surprise shallow spots in murky water

2) Submerged trees or other objects in deeper water

3) Usage by visitors

The hole in the fin above was caused by a visitor's close encounter with a submerged concrete pier 75' from shore in 4' of water.

One problem with the EPDM 'wear guard' is that most adhesives don't adhere well to the proprietary and undisclosed fin material. Best so far is McNett Seam Sealer - we had no luck with tire patch glue as suggested in another thread.

_________________
2x Revo
17' Grumman Ultralight


Top
 Profile  
 
PostPosted: Wed Aug 01, 2012 8:43 am 
Offline
Site Rank - Old Salt

Joined: Mon Jun 01, 2009 11:59 am
Posts: 606
rx7vt wrote:
3) Usage by visitors


This is most likely the part you have the least control over. And the part of most of the mishaps. Unexperienced and does not own the yak. Might want to have the "visitor" go through some training before let use the yak. Good luck.


Top
 Profile  
 
PostPosted: Wed Aug 01, 2012 1:26 pm 
Offline
Site Rank - Admiral

Joined: Thu Jul 30, 2009 12:17 pm
Posts: 163
Location: Homosassa, Florida
Not a problem.

Those look really good compared to mine. Those redfish love the shallow oyster beds.

_________________
I'm right 98% of the time. The other 3% I don't worry about.


Top
 Profile  
 
PostPosted: Wed Aug 01, 2012 4:10 pm 
Offline
Site Rank - Old Salt

Joined: Sun Aug 12, 2007 5:17 pm
Posts: 679
Location: Auckland NZ
The hot soldering iron method of repair is very effective (I have several large cuts in one of my fins which I repaired this way and they are still holding up after probably 2 years' worth of hard use).

If you have searched you will have probably found detailed info on repairing but quickly the technique is as follows:

1. cut some slivers of fin material from a 'more redundant' part of the fin - e.g. the very top of the fin right under/around the where the chain cables pass through.
2. with a hot soldering iron melt the fin material around the cut or hole and melt/paste/weld the slivers of new material in/on/around it to weld over the damage.

(I can't really describe it better than this - it is a lot easier to do than to explain. The material melts to the consistency of peanut butter and is very easy to work in that state because it holds the heat well and doesn't seem ever to get to an unworkable 'dripping' consistency. I only took one attempt to mend each of the cuts in my fin - the mends are not particularly pretty but they certainly have done the job far better than I had ever hoped)

Hope this helps.


Top
 Profile  
 
PostPosted: Wed Aug 01, 2012 4:59 pm 
Offline
Site Rank - Captain

Joined: Sat Jun 28, 2008 2:14 pm
Posts: 32
Thanks. I read about the hot melt 'peanut butter' approach in another thread, and I'll try that for my hole and a couple of cuts higher up. I mostly wanted to share my EPDM wear patch and see if there were any other preventative ideas out there for the high-risk areas at the bottom of the fins.

I will say the the EPDM is MUCH more wear and cut resistant than the Hobie material.

_________________
2x Revo
17' Grumman Ultralight


Top
 Profile  
 
PostPosted: Thu Aug 02, 2012 2:29 am 
Offline
Site Rank - Admiral

Joined: Fri Feb 25, 2011 11:02 am
Posts: 164
Location: Central New York
Goop has worked for other members, may want to jump over the this topic http://www.hobiecat.com/forums/viewtopic.php?f=26&t=44158

_________________
MrGreen


Top
 Profile  
 
PostPosted: Thu Aug 02, 2012 9:12 am 
Offline
Site Rank - Old Salt

Joined: Mon Apr 26, 2010 6:06 am
Posts: 734
Location: Amelia Island, FL
Yeap, nothing better than Marine Goop to protect your fins. I put a layer of goop on the front edges and bottom of the fins. When it starts looking narly, simply pull it off and put on a new coat.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group