Hobie Forums http://www.hobie.com/forums/ |
|
Homemade Beach Wheels http://www.hobie.com/forums/viewtopic.php?f=15&t=2740 |
Page 1 of 2 |
Author: | DougHobie17 [ Wed Nov 30, 2005 12:39 am ] |
Post subject: | Homemade Beach Wheels |
I found the article for making these finally. I made some of these and they work GREAT on soft and hard sand. Not to good on uneven ground. VERY light, just lay on hulls and tie to trailer. http://www.geocities.com/mec_coleman/tip13.htm Doug Snell 281-326-2702 |
Author: | widerisbetter [ Wed Nov 30, 2005 2:42 pm ] |
Post subject: | Cool! |
I love stuff like this. Thanks for posting this link Doug! -Stephen PS - I'm in winter mode right now and ski forums but will check here on occaison - otherwise - see ya in the spring Have a great Holiday Season |
Author: | DougHobie17 [ Fri Dec 09, 2005 10:40 pm ] |
Post subject: | Glad to Hlpe |
Let me know how they work out. Just don't put the holes in them he says. Also put a little silicone around the washers and connectors. You will love the wheels. Should be able to find barrels thru a local bottler. Find out who they sell them to? Very light, won't rust or corruce and you save a LOT of money if you don't have uneven ground. Check out our site www.tcdyc.com. Register and join in the forum. Good group of people. Doug Snell [email protected] |
Author: | ReefedOne [ Wed Mar 29, 2006 12:39 pm ] |
Post subject: | |
KUDOS! I love improvs like that. Perfect for hard-pack beaches. The various beach dollies (no names named) have always seemed a bit spendy, and not particularly UV-resistant either. With "disposable" wheels, who cares! Better than bottled Guinness--BRILLIANT! |
Author: | DougHobie17 [ Wed Mar 29, 2006 12:49 pm ] |
Post subject: | Barrels |
ReefedOne: You can order the barrels here: http://www.stores.yahoo.com/baytec/30galfoodgra.html Glad I could help. We are all trying to save money. I had to bite the bullet and get CatTrax as the uneven ground on the circuit was to much for the homemade ones. Doug Snell Hobie 17 www.tcdyc.com |
Author: | ReefedOne [ Wed Mar 29, 2006 12:56 pm ] |
Post subject: | |
Doug is a one-man real-time on-line encyclopedia... Hobie should pay him. I've seen the current prices for the "racing" Hobie 16s, so I know they've got the cash. |
Author: | DougHobie17 [ Wed Mar 29, 2006 1:03 pm ] |
Post subject: | Lot of time on hands |
I just came off of 3 years of bipolar disability and have a LOT of time to kill. I get bored so I surf. Glad to help. What do youneed info on? Doug |
Author: | ReefedOne [ Wed Mar 29, 2006 1:15 pm ] |
Post subject: | |
Addendum: If that $30 price tag is for only 1 barrel, that's way high. Guys on hurricane prep websites claim to be getting them for only $5-10 by nosing around the local distributors. That's UNrinsed, but for $20/bbl, I can do a LOT of pressure rinsing... hold it, for beach wheels, I don't HAVE to get the smell out! Rock on... Another guy claims he can buy NEW unused for $8, at a local shop. Yet another bought 8 barrels for only $3 each! Outfit your whole yacht club! Bottom line: The SHIPPING is gonna kill you, so search locally first. The recent heavy hurricane seasons have made these barrels popular, but has also increased the supply AND the number of suppliers. Please post your "scores" on this thread... as in "Dude, I scored 2 for $10 from this crooked delivery guy behind the bar and grill..." |
Author: | DougHobie17 [ Wed Mar 29, 2006 1:28 pm ] |
Post subject: | OK. |
OK, They work great. I did cut mine in half, but may work better and be lighter. Yea I go mine a long time ago and just did a search online. I didn't drive around to check locally as I don't need them anymore. So are you going to make them? Doug |
Author: | ReefedOne [ Thu Mar 30, 2006 5:34 pm ] |
Post subject: | |
I'm going to make some AFTER I get my next boat, but I'm going to acquire the barrels NOW, before the hurricane season ramps up again. I know exactly where to get the EMT conduit (axle) and other parts, but the barrels are still a question mark. Making my own custom cradles must of course also wait until the boat is in hand, and sounds like a great way to get back into working with fiberglass, Marine-Tex, etc. Judging by price, those cat-wheel makers are VERY "proud" of their products... I may have to write snide things about them all over my home-made wheels... LOL! |
Author: | Hobie Nick [ Fri Mar 31, 2006 6:59 am ] |
Post subject: | |
Easy on those production beach wheel guys. I did try to find the components that would copy those wheels. I launch over both rough terrain and soft sand so a hard wheel will not work for me. The appropriate wheel and tire are not cheap when buyng in small quantities (ie 2 pices). When I then figured in the couple of hours to build them it actually ended up being about the same price. So, I figure why not get the wheels ready to go in a few days vs. obtaining all of the materials, waiting for them to be shipped, then assembling them. It all depends on what is important to you and what your needs are. I needed a more versatile set of wheels in a short amount of time. I enjoy designing and building things (I do this for a living) but I'd rather spend my time on the water than build a set of wheels. In the off season I have plenty of other projects keeping me busy. I would say that they are one of the best accessories I have purchased for my boat. They have opened up many launchig sites previously unavailable to me in my area. |
Author: | DougHobie17 [ Fri Mar 31, 2006 8:49 am ] |
Post subject: | Production Wheels |
Guys: I am the one who found the article and posted in. I too had to bite the bullet and buy CatTrax as on the circuit in Texas and LA there is a lot of uneven ground. BUT if you are just on soft or hard sand the homemade barrel wheels are GREAT Good luck. Doug Snell Hobie 17 www.tcdyc.com |
Author: | ReefedOne [ Fri Mar 31, 2006 7:06 pm ] |
Post subject: | |
My bad... ours is a rich man's leisure hobby, and we have to pay the piper... I 'spose. Still, I like an elegant jury-rig, and these soda barrels are at least the equivalent of the 'Tiger Trax' hard-wheel dolly. (OTOH, I have 4WD so why not just drive on down to the water's edge...?) In fact, taking this barrel idea one step further, given their stiffness and those bulge-bands molded in, I wonder if you couldn't rivet several in series for a nice sail tube? Can't wait to get my hands on some barrels, and check out the WEIGHT of them. Given the runup in building materials the last 3 years... OK, I'll stop. |
Author: | DougHobie17 [ Fri Mar 31, 2006 7:15 pm ] |
Post subject: | Sail Tube |
ReefedOne: Think they would make a good sail tube. The are maybe 3/8 inch thick and should work well, Instead of rivets, why not get some thin sheets of plastic or Teflon or ? and make bands. Just cut off the ends and band together. Could make a shelf for one end. I think it would work good. Let me know how it comes out. My friend Danny took my article link and designed his own wheels. Check these out. The came out great!!! http://dgaleana2.proboards56.com/index. ... 1143785090 Doug Snell Hobie 17 Soon to be Mystere 4.3 www.tcdyc.com |
Author: | ReefedOne [ Mon Apr 03, 2006 4:10 pm ] |
Post subject: | |
Your friend's dolly came out nice, but the judges must deduct points for cheating by using ready-made wheels... and for not hammer-forging his own axle out of empty beer cans, LOL! I'm a little leary of making a sail tube in such a segmented fashion, due to the bumpy interior, and the increased opportunities for rain intrusion. OTOH with the run-up in building materials (real estate boom + hurricanes) I'm not sure what the sticker shock is on large diameter thin-wall PVC duct tubing and end caps these days. Off hand, what are the best ways to attach round tubes to trailer frames? Could you elaborate on your banding idea? Are these barrels flexible enough to be friction fitted with bands? How do you envision tightening/cinching the bands? |
Page 1 of 2 | All times are UTC - 8 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |