Hobie Cat Forums

It is currently Fri Aug 01, 2014 7:40 am

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: My ball is always loose
PostPosted: Thu Aug 20, 2009 5:26 pm 
Offline
Site Rank - Old Salt

Joined: Fri Dec 28, 2007 11:23 am
Posts: 526
Location: Lake Norman NC
Is there any way to tighten the mast rotator ball and keep it from turning
I live in fear that it wolk out and let the mast fall
I have used vice grips
silicone
5200
The ball still turns
Hobie 21 SE

December got the boat on the trailer ball would only move a little bit
My ball was not in danger of coming off
I will try Matt's idea to polish the base I might try some Loc tite blue


Last edited by gary eudy on Mon Nov 30, 2009 6:09 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Thu Aug 20, 2009 5:28 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 8918
Location: Oceanside, California
Polish the mast base cup and use some grease to make that connection slip easier.

_________________
Matt Miller
Director of Parts and Accessory Sales
Hobie Cat USA


Top
 Profile  
 
PostPosted: Fri Aug 21, 2009 3:37 am 
Offline
Site Rank - Admiral

Joined: Sun Sep 17, 2006 9:34 am
Posts: 262
Location: Banana River , Fl
Nothing worse than having loose balls....

_________________
TC


Top
 Profile  
 
PostPosted: Wed Sep 09, 2009 8:47 pm 
Offline
Site Rank - Deck Hand

Joined: Wed Sep 09, 2009 7:57 pm
Posts: 18
Location: Denver & Lake McConaughy NE
Or loosing the LONG Shaft attached to it when it ball falls off. Sorry, I couldn't resist....

Dan

_________________
Dan
Nacra 5.8 #656 "Una Más"
Capri Cyclone
No longer own Hobie 21SE #270
Denver & Lake McConaughy, Nebraska


Top
 Profile  
 
PostPosted: Mon Nov 09, 2009 12:36 pm 
Offline
Site Rank - Captain

Joined: Mon Nov 09, 2009 8:21 am
Posts: 25
Location: Loganville, GA
Hm, I'd think that wrapping a largish sized wide rubber band around that shaft could keep it from slipping through the holes if the ball came off.

_________________
- Andy
=> Hobie Cat 14 <=
=> 1978 Chrysler 26' Herreschoff Designed Monohull <=


Top
 Profile  
 
PostPosted: Mon Nov 09, 2009 4:14 pm 
Offline
Site Rank - Admiral

Joined: Mon Mar 30, 2009 7:29 pm
Posts: 228
Location: North Bend, WA
Unknowing to me, when I purchased the boat and was dry rigging in the yard my ball was loose. I raised the mast and lowered two times with no problem. I then lowered the mast with no support behind the rear trailer mast support and this caused an uplift on the ball and it came off....Scared the $#^&*($% out of us when the mast fell to the ground and luckily no one was hurt. I purchased a new ball and I used one of those Craftsman rubber band wrenches to tighten and it worked great. The ball is still tight and I check everytime before I hook the mast to it. I would not use vice grips as this would marr the surface.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group