Return to Hobie.com
Hobie Forums
It is currently Thu Mar 28, 2024 1:40 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Sat Apr 13, 2013 7:54 pm 
Offline
Site Rank - Captain

Joined: Sun Apr 26, 2009 9:22 am
Posts: 28
Location: Shalimar FL
The area under the set screw on my mirage drive spine cracked. The set screw lands on a flat on the shaft for the fins. The dealer said the spine is only around $20 (US), but since my fin shaft had already slipped out of place twice due to the screw backing out, I opted for what I think may be a better solution:
Image

I drilled holes through the shaft and spine, and I sawed off half of the threads for the set screw. Here is the final product:

Image

Image

That's a 4-40 UNC stainless screw with a self locking nut in a 7/64 inch thru hole. The fix has been working great. See my web site at the link below if you would like more details.

_________________
Greg
Red 2017 AI and red TI 2019


Last edited by Surfoos on Sat Apr 13, 2013 8:22 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Sat Apr 13, 2013 8:20 pm 
Offline
Site Rank - Admiral

Joined: Tue Apr 13, 2010 10:07 pm
Posts: 169
Exellent repair - I too have had problems in this area.

Hobie engineers please take note


Top
 Profile  
 
PostPosted: Sun Apr 14, 2013 9:47 am 
Offline
Site Rank - Captain

Joined: Sun Apr 26, 2009 9:22 am
Posts: 28
Location: Shalimar FL
davew wrote:

Hobie engineers please take note


True...a metal set screw in plastic threads pushing on an immovable steel part causing permanent strain in a thinned area of plastic under cyclic loading... I suspect it will not age well. A screw in double shear is usually a preferred connection. Maybe they were worried about corrosion of small parts, parts count, or the need for another tool (a #1 small cross point screwdriver).

This fix may have been easier than replacing the spine. I just punched the fin shaft out, drilled, then hammered it back in. Did not mess with the cables or the idler pulley. The process I feared was drilling through the stainless steel shaft. All I had was a hand drill (no press). Turned out, with a little oil and a sharp bit, it only took a few minutes of drilling.

Another tid-bit: The drive started clicking when the set screw came loose. I doubt it was the sound of the loose set screw tapping the flat on the shaft - I usually blame clicking on the cable to gear teeth alignment - but the drive does seem to operate more smoothly now. If I were a Hobie engineer I would consider purposefully loosening the set screw a turn or two and see if it causes clicking. That clicking sound is so annoying.

_________________
Greg
Red 2017 AI and red TI 2019


Top
 Profile  
 
PostPosted: Mon Apr 15, 2013 4:59 am 
Offline
Site Rank - Old Salt

Joined: Thu Aug 16, 2007 2:25 pm
Posts: 2863
Location: Central Coast NSW Australia
Nice fix. 8)
Should be in the 'Repairs/Problems' section.


Top
 Profile  
 
PostPosted: Mon Apr 15, 2013 1:38 pm 
Offline
Site Rank - Admiral

Joined: Tue Apr 13, 2010 10:07 pm
Posts: 169
The shaft also needs a screw driver slot at the ends to allow alignment adjustment.


Top
 Profile  
 
PostPosted: Mon Apr 15, 2013 5:17 pm 
Offline
Site Rank - Admiral

Joined: Sun Sep 14, 2008 9:09 pm
Posts: 187
Location: Sayville, NY
davew wrote:
The shaft also needs a screw driver slot at the ends to allow alignment adjustment.


That's a great, simple idea. Certainly would make aligning the shaft when
re-assembling a lot easier.

_________________
Bob
Proud member Kayak Fishing Association of New York


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group