Return to Hobie.com
Hobie Forums
It is currently Thu Mar 28, 2024 4:03 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 17 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: Sun Mar 11, 2012 3:40 am 
Offline
Site Rank - Captain

Joined: Wed Aug 31, 2011 6:35 am
Posts: 53
Location: Canberra, Australia
Some of my favourite camping spots are really close (200-500m) to a launching site, but I have found a fully laden TI to be a killer on my back. So, I designed a simple jockey wheel that I sit under the mast step. This allows me to easily pull the TI to the launching site without straining my back. Yes it's only suitable for hard surfaces (or firm sand).

Image

Image

Image
Image
Image

_________________
Rob,

Image
2011 Hobie TI


Top
 Profile  
 
PostPosted: Sun Mar 11, 2012 9:38 am 
Offline
Site Rank - Admiral

Joined: Mon May 02, 2011 8:48 am
Posts: 159
Location: Southwest Calif.
You people on this forum never cease to amaze me with the innovations and mods you invent for the Hobie lines.

I like this idea, good job !!

_________________
Image


Top
 Profile  
 
PostPosted: Sun Mar 11, 2012 10:28 am 
Offline
Site Rank - Old Salt

Joined: Fri Jan 05, 2007 9:21 pm
Posts: 2498
Location: Central Florida
Very nice!

Now you need to create a parking break, or don't forget to NOT let go of it on a ramp! :lol:

_________________
Image
Hobie Island Sailing since 2006


Top
 Profile  
 
PostPosted: Sun Mar 11, 2012 8:28 pm 
Offline
Site Rank - Captain

Joined: Wed Aug 31, 2011 6:35 am
Posts: 53
Location: Canberra, Australia
Hi KayakingBob,

You're so right about not letting go! Thankfully most of the ramps I use have a fairly gentle slope otherwise I couldn't pull the TI up the ramp after a long sail! (Hmm, but what will I do if I do find a steep ramp?) Electric winch???

Somewhere in the distant past I do remember saying to my wife that I wouldn't need to spend any money on the TI after purchasing it, but adding mods is just so much fun!

_________________
Rob,

Image
2011 Hobie TI


Top
 Profile  
 
PostPosted: Mon Mar 12, 2012 2:11 pm 
Offline
Site Rank - Old Salt

Joined: Tue May 18, 2010 2:31 pm
Posts: 3068
Location: Kailua 96734
Nice landing gear Rob!

_________________
The Wind Is Your Friend...


Top
 Profile  
 
PostPosted: Tue Mar 13, 2012 2:21 am 
Offline
Site Rank - Old Salt

Joined: Wed Nov 26, 2008 4:36 am
Posts: 837
Location: Gippsland Lakes Victoria Australia
Nic
That is excellent!! 8) :wink:
I will show this to my mate who came up with something similar a year or so ago using a trailer jockey wheel. He is not entirely happy with it because the bearings are failing due to salt water submersion.
Your approach looks like it may solve this issue.
I also think your solution is MUCH more practical & economical than the huge Hobie TI Dolly Cart that I have.
The TI is a real hernia creator without something more than a scupper cart!
Particularly in sand!
I originally ordered the heavy duty foam filled wheels and cart. However i am reluctant to use it because it s only joined together by silver solder :shock: little wonder that these carts have fallen apart! The other issue of concern is the enormous stress on the scupper holes using this type of cart with a fully assembled and loaded TI, dragging it across sand or mud :o :shock: : :roll:
Great work - thanks for sharing. Make sure you contact me ( & the local " gang" if you ever come over to our pond and we'll look after you and share lur local knowledge :wink:

_________________
Mickey
2016 AI Hibiscus
purchased NEW Nov 2021 - My 5th
Adventure Island Sailing since 2008


Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 1:31 am 
Offline
Site Rank - Old Salt

Joined: Thu Aug 16, 2007 2:25 pm
Posts: 2863
Location: Central Coast NSW Australia
Very nice work Rob! 8)
It would certainly make wheeling the TI when the cart is in the rear scuppers a lot easier.
You know maybe you could name your TI the "Reliant" or "Robin"! :wink:

mickeymouse wrote:
However i am reluctant to use it because it s only joined together by silver solder :shock: little wonder that these carts have fallen apart!

:shock:
Mickey are you sure it's just silver solder?
I've had 3 Trax carts and they've all been welded stainless. Mind you the welds are pretty poor and have needed re-welding over time.


Last edited by stringy on Thu Mar 15, 2012 2:41 am, edited 1 time in total.

Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 2:21 am 
Offline
Site Rank - Old Salt

Joined: Fri May 08, 2009 5:06 am
Posts: 1701
Location: Lake Macquarie NSW AUSTRALIA
Great mod Rod.

_________________
Image

Don't take life too seriously................it ain't permanent.


Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 3:35 am 
Offline
Site Rank - Old Salt

Joined: Wed Jan 25, 2012 5:30 am
Posts: 429
Location: Gulf Shores, Alabama
That is really a slick mod !!! Nice Job.

Looks like it's something that might work well during the 40 mile portage in the Watertribe UFC.


Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 12:34 pm 
Offline
Site Rank - Old Salt

Joined: Wed Nov 26, 2008 4:36 am
Posts: 837
Location: Gippsland Lakes Victoria Australia
stringy wrote:
Very nice work Rob! 8)
It would certainly make wheeling the TI when the cart is in the rear scuppers a lot easier.
You know maybe you could name your TI the "Reliant" or "Robin"! :wink:

mickeymouse wrote:
However i am reluctant to use it because it s only joined together by silver solder :shock: little wonder that these carts have fallen apart!

:shock:
Mickey are you sure it's just silver solder?
I've had 3 Trax carts and they've all been welded stainless. Mind you the welds are pretty poor and have needed re-welding over time.

Stringy - i don't profess to be an expert on this, but one of my mates was a car motor body builder (made hearses & stretch limos) & has 2 AIs. He told me that's all it is :o I am only referring to the HD cart with the foam filled tyres. It looks much worse than the other carts as it clearly has just a few spot soldered joints..

_________________
Mickey
2016 AI Hibiscus
purchased NEW Nov 2021 - My 5th
Adventure Island Sailing since 2008


Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 7:19 pm 
Offline
Site Rank - Old Salt

Joined: Tue Oct 18, 2011 3:33 pm
Posts: 338
Location: Adelaide, South Australia
Our dealer is South Australia has the carts fully MIG/TIG welded with stainless rod before selling. Im sure that is from experience.
Just a pity I put holes in the scuppers and had to weld them closed.
Anyone in SA looking for a Hobie cart with foam filled tyres?

_________________
Cheers, Brian in South Australia
Tandem Island -
Image


Top
 Profile  
 
PostPosted: Mon Jan 07, 2013 4:18 am 
Offline
Site Rank - Old Salt

Joined: Sat Nov 21, 2009 8:45 pm
Posts: 343
Location: Melbourne, Australia
This is EXACTLY what I need!

I find the A.I. a killer to haul the 400m from the beach to my house (350m of that is on firm dirt and sealed roads), so I can only imagine that a fully rigged T.I. would be a nightmare.

I'm off to Bunnings tomorrow to hunt down some suitable parts!

Any pointers or info on the materials and methods used would be great :-)

Thanks for the inspiration!

Mike.


Top
 Profile  
 
PostPosted: Tue Jan 08, 2013 2:31 am 
Offline
Site Rank - Captain

Joined: Wed Aug 31, 2011 6:35 am
Posts: 53
Location: Canberra, Australia
Hi Mike,

I purchased the wheel from a specialist wheel supplier in Adelaide. However, upon further research, I think the wheel was initially intended for a wheelchair. I'm not sure if the wheel bearings are stainless steel, hence I have limited saltwater immersion.

I have also added extra lateral bracing to my original design as I found the hull supports not strong enough. Apart from the wheel, all materials can be obtained from a hardware store.

Rob.

_________________
Rob,

Image
2011 Hobie TI


Top
 Profile  
 
PostPosted: Tue Jan 08, 2013 5:42 am 
Offline
Site Rank - Old Salt

Joined: Sat Nov 21, 2009 8:45 pm
Posts: 343
Location: Melbourne, Australia
Hi Rob,

Thanks for the info - don't suppose you can tell me the make/model of the wheel? :-)

Also, I can see that you've attached some sort of heavy-duty carpeting to the supports - is that attached via pop-rivets?

Cheers,

Mike.


Top
 Profile  
 
PostPosted: Wed Jan 09, 2013 12:04 am 
Offline
Site Rank - Captain

Joined: Wed Aug 31, 2011 6:35 am
Posts: 53
Location: Canberra, Australia
Hi Mike,

Unfortunately the castor does not have any branding, but it appears to be cast aluminium. The tyre itself is a pneumatic tyre 200mm * 50mm, by Cheng Shin. Fits standard rim 27.5 * 93mm.

I scanned the catalogue from the company that I purchased the wheel & castor from, but they don't appear to be selling it anymore.

The carpet is an off-cut of marine carpet & was glued on using Marine Black Silicon. (However, any fine carpet will do.) The webbing was riveted on, then the carpet glued over the top. I also sealed all joints with the silicon to help reduce the chance of corrosion between the joints. (Note: Do not use Clear 'household' silicon on aluminium as it is corrosive).

I hope this helps.

Rob.

_________________
Rob,

Image
2011 Hobie TI


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 17 posts ]  Go to page 1, 2  Next

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group