Return to Hobie.com
Hobie Forums
It is currently Thu Mar 28, 2024 12:59 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: DIY rudder casting shims
PostPosted: Wed Jun 06, 2012 5:43 am 
Offline
Site Rank - Captain

Joined: Wed Jun 30, 2010 2:24 pm
Posts: 112
Location: Todd Mission, Texas
Amateur tip - Make shims out of used plastic food container lids (I know this may be common knowledge, but I thought I'd post anyway.)
For the Hobie 17(/18 upgraded) rudders "Molly McButter" bottles are nearly the same sizs as the contact area for the upper castings. The lowers are smaller.
I used 2 "I Can't Believe It's Not Butter" lids and made 8 shims.

1) Eat baked potatoes, with all the fixins (especially bacon), and put I Can't Believe It's Not Butter tub lids in the special basket in dish washer (so they dont fly all over and melt onto the heating element).

2) Trace appropriately sized circular object onto lids as many times as you can.

3) Cut shims out with scissors.

4) Punch holes in center for bolt. I used a hole punch and "nibbled" out the hole till it fit.

5) Install on rudders.

6) Look at crew, and say (using a Fabio voice) "I Can't Believe It's Not Rudder...........Shims" :mrgreen:

7) Laugh hysterically, then explain the Fabio reference to crew. Youtube is your friend here.

For you skinny, health conscious, people, you can use Crisco lids and make more, but omit steps 6 & 7

_________________
Jeff
1986 Hobie 18 #13031


Top
 Profile  
 
PostPosted: Wed Jun 06, 2012 6:37 am 
Offline
Site Rank - Old Salt

Joined: Mon May 09, 2005 10:25 am
Posts: 4176
Location: Jersey Shore
Or, for the super lazy type...

Cut out pieces of milk jug (1" square, round if you want to be fancy). Jam as many in between the housing and rudder as will fit to be snug. Insert pivot bolt. Use hammer to punch bolt through shims. Install nut onto bolt.

sm


Top
 Profile  
 
PostPosted: Wed Jun 06, 2012 7:36 am 
Offline
Site Rank - Old Salt

Joined: Fri Oct 17, 2008 2:21 pm
Posts: 379
Location: Winston Salem, NC
I use milk jugs for shims also but I have a 2" diam. hole saw with a 1/4" bit. I simply cut the discs on a drill press.

_________________
Howard


Top
 Profile  
 
PostPosted: Wed Jun 06, 2012 8:48 am 
Offline
Site Rank - Captain

Joined: Wed Jun 30, 2010 2:24 pm
Posts: 112
Location: Todd Mission, Texas
so baked potatoes or Oreos/Frosted Flakes can be used to make shims... I wonder what I can use a Jack Daniels bottle for on the boat.... :mrgreen:

_________________
Jeff
1986 Hobie 18 #13031


Top
 Profile  
 
PostPosted: Wed Jun 06, 2012 8:55 am 
Offline
Site Rank - Old Salt

Joined: Fri Apr 13, 2012 7:35 pm
Posts: 626
Location: Tuscaloosa, AL
presto13031 wrote:
so baked potatoes or Oreos/Frosted Flakes can be used to make shims... I wonder what I can use a Jack Daniels bottle for on the boat.... :mrgreen:


Seal it up really well and use it for a mast float.


Top
 Profile  
 
PostPosted: Wed Jun 06, 2012 9:49 am 
Offline
Site Rank - Old Salt

Joined: Sun Dec 23, 2007 1:20 pm
Posts: 493
Location: Clearwater, FL
David Hall wrote a great article: Towards the "No Slop" Rudder in the March 1997 issue of: On The Wire

https://www.thebeachcats.com/OnTheWire/earthlink/_mattson/hobie/archives/v1-i7/feature1.htm

_________________
Tim
84 H16
82 H16
87 H14T
Tortola Sails: 115222
Blue Prism Sails: 88863
Clearwater, FL
Image


Last edited by Tim H16 on Tue May 18, 2021 10:25 am, edited 1 time in total.

Top
 Profile  
 
PostPosted: Wed Jun 06, 2012 10:07 am 
Offline
Site Rank - Old Salt

Joined: Mon Sep 20, 2004 12:36 pm
Posts: 788
Location: Tri-Cities, WA
I must be old school. I too make my own shims but from a 12"x12", 1/16" PTFE Sheet (Dupont calls it Teflon). It cost about $25.00 for the sheet, but so far a set of 4 - 2" dia washers,1/side/blade, has lasted me 5 hard years of sailing with no noticeable wear. They work great with virtually no slop in the rudders. Not as cheap and sexy as a Pringles lid, but well worth the price. :wink:

P.S. I made 3 washer sets total, and still had half the sheet left which I have used for other projects as well. 8)


Top
 Profile  
 
PostPosted: Tue Jun 19, 2012 9:22 am 
Offline
Site Rank - Captain

Joined: Wed Sep 07, 2011 8:16 am
Posts: 50
Location: West Michigan (Grand Rapids, Holland Area)
Nylon Washers are much more popular now than they used to be also, most hardware stores and big box stores carry them, if not you can get them from mcmastercarr pretty cheap also.
We use quite a few of them at work so I use the ones that I pick up off the shop floor.

_________________
Cesar (Cez) S.
H16 - "He gone!"


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
© Hobie Cat Company. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group