Hobie Cat Forums

It is currently Tue Jul 22, 2014 3:33 pm

All times are UTC - 8 hours [ DST ]




Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 4 posts ] 
Author Message
 Post subject: Hobie 16 FAQ
PostPosted: Fri Jun 05, 2009 11:05 am 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 8889
Location: Oceanside, California
Image

Specifications
Length: 16' 7"
Beam: 7' 11"
Mast Length: 26' 6"
Sail Area: 218 Sq. Ft.
Weight: 320 lbs.
Hull Construction: Fiberglass/Foam Sandwich

H16 Owners Manual: http://static.hobiecat.com/digital_assets/H16_Manual.pdf

Hobie 16 Parts Guide: http://static.hobiecat.com/digital_assets/H14-16_Parts.pdf

Support Pages: http://www.hobiecat.com/support/index-sail.html

Rigging Video

The following video was produced in the late 80's, but has some good information that pertains to all vintages of Hobie 16s. Jib halyard systems, sheeting systems have changed a number of times over the years. This video addresses the configuration at that time.


_________________
Matt Miller
Director of Parts and Accessory Sales
Hobie Cat USA


Top
 Profile  
 
PostPosted: Tue Jun 16, 2009 11:24 am 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 8889
Location: Oceanside, California
Hobie 16 mast step replacement.

This was written up in the Hotline (starts on page 14):

http://static.hobiecat.com/2010_archive/hobieclass/eHCA_News01_02-05.pdf

_________________
Matt Miller
Director of Parts and Accessory Sales
Hobie Cat USA


Top
 Profile  
 
PostPosted: Wed Mar 24, 2010 1:35 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 8889
Location: Oceanside, California
Recent Hobie 16 trampolines have an added grommet at the rear corners. The following sequence shows proper lace routing.

Rear lacings start at the outboard sides of the rear castings.

Image

Image

Image

Finish off with half hitches in the center rear area. The example shown has routed the lines back (doubled over) to use up excess line.

Image

_________________
Matt Miller
Director of Parts and Accessory Sales
Hobie Cat USA


Top
 Profile  
 
PostPosted: Tue May 20, 2014 1:47 pm 
Offline
Site Admin

Joined: Tue May 27, 2003 12:44 pm
Posts: 8889
Location: Oceanside, California
On a 14 or 16 you can "pre-bend" the sidebars before tensioning the center lace. We do not use double grommets down the center and get tight tramps without a huge effort.

Image

Use the mainsheet system. Lay the blocks and line on the tramp "unsheeted" from side to side bar... in the center. Add a line to the base of the blocks that can reach around the sidebar, under the tramp and meet the top block. Tie off. Pad the side bars with some cardboard where the line goes around the sidebars. Sheet the system to bend the sidebars in by over 1". We sheet till the tramp gets a little pucker shape along the sidebar. Cleat the blocks and tighten the tramp using moderate tension. Using the vise grips, dowell or just holding the line at each grommet as you go. Tension the aft lace last and then release the block set.

We use this system and get over 1-2 inches of prebend in the bars for over 1 inch after releasing.

Worst loads on a grommet are during tensioning each one... this saves effort and grommets.

_________________
Matt Miller
Director of Parts and Accessory Sales
Hobie Cat USA


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 4 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group